Flow Bench · Free calculator
Velocity stack length calculator
Enter the engine speed you want help at and get the intake lengths that put the pressure wave there, or enter a length and see the speeds it is tuned for. Three published formulas, no fitted numbers, every source below.
For racing use only.
How it works
What the calculator does with your numbers
-
The speed of sound
From the air temperature, by the U.S. Standard Atmosphere's formula for dry air: 340.3 m/s at 15 °C, 346.1 m/s at 25 °C. Humidity is not included.
-
The pipe's own note
With the valve shut, the intake is a pipe closed at one end and open at the other. The air in it swings at the speed of sound divided by four times the pipe's length. A 230 mm intake rings at about 350 Hz.
-
The rule that was measured
In 1944 NACA varied the inlet pipe on a single-cylinder engine at fixed speeds and recorded the power. It found, in its own words, "three distinct optimum lengths of inlet pipe", where the pipe's note was slightly more than 3, 4 and 5 times the valve's frequency, and gave the lengths as "slightly less than 30 c/Nq": thirty times the speed of sound, over the engine speed times 3, 4 or 5. The calculator gives that length for each.
-
The open end
The wave does not turn around exactly at the end of the pipe but a little past it: 0.61 of the mouth's radius when the end stands free, 0.82 when it is flush with a wall. The calculator takes that off, so the answer is the length to build.
Read this before you cut anything
What it cannot tell you
- Which length is best. It gives three candidates. The engine NACA tested gained 15 to 20 percent over no pipe at each of them.
- Exactly where the peak lands. NACA's best lengths were "slightly less" than the formula's, and the end corrections are for still air at low frequency. A bellmouth's is not well pinned down: one racing-engine study assumed 10 to 14 mm on a 50 mm pipe and found the real figure differed.
- What the valve timing does. NACA found that a longer pipe wants the inlet valve to close later. The calculator knows nothing about your cams.
- High engine speeds. The rule was measured at 1,000 to 1,600 rpm. On a racing engine at 13,000 rpm, Harrison and Dunkley concluded that "inertial ram effects make a strong contribution to the intake process at high engine speeds whereas acoustic resonance effects are more important to the rather weak wave action that occurs at low engine speeds."
- The airbox, the neighbors and the shape of the mouth. How much air a stack passes, and how its neighbors and the airbox walls change that, is what Flow Bench is for. The guide to the lip and its radius has what the mouth alone is worth.
- Power. No calculator turns a length into horsepower. A dyno does.
Sources
Where every number comes from
- Boden and Schecter, "Dynamics of the inlet system of a four-stroke engine", NACA Technical Note 935, 1944. The tuning rule. A single-cylinder test engine, inlet pipes from 9 to 247 inches, 1,000 to 1,600 rpm.
- Capetti, "Effect of intake pipe on the volumetric efficiency of an internal combustion engine", NACA Technical Memorandum 501, 1929. An earlier statement of the same rule at one wave order. Its table of lengths is one of the checks the calculator has to pass.
- Harrison and Stanev, "A linear acoustic model for intake wave dynamics in IC engines", Journal of Sound and Vibration 269 (2004) 361-387. The resonance of an intake pipe with the valve closed: the speed of sound over four times its length.
- Harrison and Dunkley, "The acoustics of racing engine intake systems", Journal of Sound and Vibration 271 (2004) 959-984. The same resonance on a racing engine at 13,000 rpm, and the finding that inertia matters more than resonance at high speed.
- Silva, Guillemain, Kergomard, Mallaroni and Norris, "Approximation formulae for the acoustic radiation impedance of a cylindrical pipe", Journal of Sound and Vibration 322 (2009) 255-263. How far past an open end the wave turns around: 0.6133 of the radius for a free end and 0.8216 for one flush with a wall, after Levine and Schwinger (1948) and Norris and Sheng (1989).
- U.S. Standard Atmosphere, 1976 (NOAA, NASA and the U.S. Air Force). The speed of sound in dry air at a given temperature.
FAQ
Stack length, answered
The questions behind the numbers.
How do I calculate velocity stack length?
Work out the speed of sound for the air temperature, divide 30 times that speed by the engine speed in rpm times a wave order of 3, 4 or 5, and take off the open end’s correction (0.61 of the mouth’s radius for a free end). The result is the length from the valve to the open end, port and throttle body included. At 11,000 rpm and 25 °C with a 60 mm mouth that gives about 296, 218 and 170 mm.
What is a wave order?
How many times the air in the closed intake pipe swings back and forth in the time between one opening of the valve and the next. NACA Technical Note 935 measured its best power where that number was slightly more than 3, 4 or 5. A higher order means a shorter pipe for the same engine speed.
Which of the three lengths should I build?
The calculator cannot tell you. On the engine NACA tested, all three gave 15 to 20 percent more mean effective pressure than no pipe at all. Packaging usually decides: on a motorcycle only the shortest one or two fit under the tank. Which is best on your engine is a question for a dyno.
Does a longer velocity stack make more low-end power?
A longer intake moves the tuned speeds lower: the tuned speed is inversely proportional to the length, so 10 percent more length moves each tuned speed about 9 percent down. Whether that is worth having depends on where the engine needs help and what the valve timing does with it.
Where do I measure the length from?
From the intake valve, along the middle of the port, the throttle body and the stack, to the open end. The stack is only the part you can change. The source measured plain pipes on a test engine and gives no rule for the bends and changes of section inside a real port, so treat a few millimeters as unknown.
Is the calculator accurate for a high-revving motorcycle engine?
The rule was measured at 1,000 to 1,600 rpm on a large single. On a Formula 1 test cylinder at 13,000 rpm, Harrison and Dunkley found the closed-valve oscillation close to six times the valve frequency, and concluded that inertia matters more than resonance at high engine speeds. So the lengths here are a sound place to start a test from, not a prediction of where your torque peak will be.
Flow Bench
Tell me when Flow Bench opens
The calculator gives a length. Flow Bench shows how the stack you build to that length flows. One email on the day it opens, and a short note when it adds a new kind of part.
A message is on its way with a link in it. Open that link and you are on the list. Nothing else gets sent until you do.
That did not come through with an email address in it. Try once more.
That is several signups from one connection in a row. Wait a minute and try again.
Follow along
Follow the trip
We'll post photos, video, and the next morning's plan as we go.